Beijer-electronics RBC EN Instrukcja Użytkownika

RBCUser’s GuideEnglishMAEN986C, 2012-05

Firmware2FirmwareThe internal firmware is responsible for all s oftware tasks r unning on the RBCmodule, especially the SCOM command handling, USB, RS2

Firmware2.1.1 Using Software Settings Instead ofDIP SwitchesThe DIP switches can be used to adjust the mode of the serial interfaces as well asthe mon

Firmware2.1.4 Startup Brightness ModeThe Startup Brightness Mode specifies backlight brightness after power on orreset, in one of the following ways:•

Operation3Operation3.1 RBC DriverThe RBC hardware is based on a Microchip Technology Inc. controllersupporting USB. Microchip provides a General Purpo

Operation1.In the first window select No, not this time, and click Next.2.Select Install from a list or specific location (Advanced),andclickNext.Beijer

Operation3.Select the path to the driver, and click Next.On the MTe/EPC C2D Nautic Driver and Documentation CD, the driveris located at (CD-ROM):\EPC_

Operation3.2 SCOM ProtocolThe implemented SCOM Protocol is designed for remote controlling of differentdevices over different kinds of inter faces. It

Operation3.3.1 Remote DimmingThe Remote Dimming feature allows build ing local networks of connectedmonitors where any monitor can control the backlig

OperationUSB NetworkSeveral monitors can control each other if they have a USB connection to the samePC. To enable this feature, the RBC Router must r

OperationGlobal Universal NetworkSeveral monitors in different local networks can control each other if they areconnected via Ethernet, RS232 (only tw

ForewordRBC ManualForewordThe Remote Backlight Controller (RBC) module is a part of the MTe monitorseries and of the EPC C2D Nautic series. The main p

Operation3.6 Additional SoftwareNote:The delivered software is for Windows operating systems only. It was written forWindows XP and Windows 7.The soft

Operation• specifying the time-out for clearing the answer bufferThe RBCRouterConfigurator must be called on the same PC where the RBCRouter is running

Operation3.6.3 RBC ViewerThe tool RBCViewer.exe, part of the Monitor Control Center, offers a convenientway to show all monitors connected to a PC. Al

MTe Monitor Ports Drawing4 MTe Monitor Ports DrawingOFFON51 1 1 4 2DIP switchesPower remoteBuzzer in/out COM A COM BBeijer Electronics, MAEN986C2

Troubleshooting5TroubleshootingIf the monitor detects an error, it beeps twiceatstartupandsetsthefactorydefaultsettings. Any customer settings will be

Head officeBeijer Electronics ABBox 4 2620124Malmö,Swedenwww.beijerelectronics.com / +46 40 358600

ContentsContents1 Hardware ... 41.1 Interfaces ...

Hardware1 HardwareAn RBC module is a built-in part of an EPC C2D Nautic or an MTe monitor.Supported features depend on the device.Component Function D

Hardware1.1 InterfacesRelated informationMTe Monitor Ports Drawing1.1.1 COM A and COM B Pin C onfigurationThe COM A and COM B ports are 9 pin D-SUB fem

Hardware1.1.2 Buzzer In/Ou t Pin ConfigurationThere is a buzzer integrated in the front behind the front foil. It can be turned onor off by a SCOM comp

Hardware1.1.4 USB InterfaceTheUSBinterfaceoftheRBCmodulecannotbeaccesseddirectlybyaplug.In an EPC, the USB interface is built-in and internally connec

Hardware1.2 DIP SwitchesThe DIP switches can be used to adjust the mode of the serial interfaces as wellas the monitor address.The four DIP switches t

Hardware4.Make the desired DIP switch settings.5.Replace the back cover.1.2.2 Serial Mode DIP Switch SettingsDIP switch 5 is used to set COM A and COM